Specific gravity

It has been suggested that this article be merged into Relative density. (Discuss) Proposed since August 2018.

Specific gravity  

Common symbols

SG 
SI unit  Unitless 
Derivations from
other quantities 
Specific gravity, also called relative density, is the ratio of the density of a substance to the density of a reference substance; equivalently, it is the ratio of the mass of a substance to the mass of a reference substance for the same given volume. Apparent specific gravity is the ratio of the weight of a volume of the substance to the weight of an equal volume of the reference substance. The reference substance for liquids is nearly always water at its densest (at 4 °C or 39.2 °F); for gases it is air at room temperature (20 °C or 68 °F). Nonetheless, the temperature and pressure must be specified for both the sample and the reference. Pressure is nearly always 1 atm (101.325 kPa).
Temperatures for both sample and reference vary from industry to industry. In British beer brewing, the practice for specific gravity as specified above is to multiply it by 1,000.^{[1]} Specific gravity is commonly used in industry as a simple means of obtaining information about the concentration of solutions of various materials such as brines, hydrocarbons, antifreeze coolants, sugar solutions (syrups, juices, honeys, brewers wort, must, etc.) and acids.
Contents
Details [ edit ]
Being a ratio of densities, specific gravity is a dimensionless quantity independent of the systems of units used to make measurements. Specific gravity varies with temperature and pressure; reference and sample must be compared at the same temperature and pressure or be corrected to a standard reference temperature and pressure. Liquids with a specific gravity of 1 are neutrally buoyant in water. Those with SG greater than 1 are denser than water and will, disregarding surface tension effects, sink in it. Those with an SG less than 1 are less dense than water and will float on it. In scientific work, the relationship of mass to volume is usually expressed directly in terms of the density (mass per unit volume) of the substance under study. It is in industry where specific gravity finds wide application, often for historical reasons.
True specific gravity of a liquid can be expressed mathematically as:
where ρ_{sample} is the density of the sample and ρ_{H2O} is the density of water.
The apparent specific gravity is simply the ratio of the weights of equal volumes of sample and water in air:
where W_{A,sample} represents the weight of the sample measured in air and W_{A,H2O} the weight of an equal volume of water measured in air.
It can be shown that true specific gravity can be computed from different properties:
where g is the local acceleration due to gravity, V is the volume of the sample and of water (the same for both), ρ_{sample} is the density of the sample, ρ_{H2O} is the density of water, W_{V} represents a weight obtained in vacuum, is the mass of the sample and is the mass of an equal volume of water.
The density of water varies with temperature and pressure as does the density of the sample. So it is necessary to specify the temperatures and pressures at which the densities or weights were determined. It is nearly always the case that measurements are made at 1 nominal atmosphere (101.325 kPa ± variations from changing weather patterns). But as specific gravity usually refers to highly incompressible aqueous solutions or other incompressible substances (such as petroleum products), variations in density caused by pressure are usually neglected at least where apparent specific gravity is being measured. For true (in vacuo) specific gravity calculations, air pressure must be considered (see below). Temperatures are specified by the notation (T_{s}/T_{r}), with T_{s} representing the temperature at which the sample's density was determined and T_{r} the temperature at which the reference (water) density is specified. For example, SG (20 °C/4 °C) would be understood to mean that the density of the sample was determined at 20 °C and of the water at 4 °C. Taking into account different sample and reference temperatures, we note that, while SG_{H2O} = 1.000000 (20 °C/20 °C), it is also the case that SG_{H2O} = ^{0.998203}⁄_{0.999840} = 0.998363 (20 °C/4 °C). Here, temperature is being specified using the current ITS90 scale and the densities^{[2]} used here and in the rest of this article are based on that scale. On the previous IPTS68 scale, the densities at 20 °C and 4 °C are 0.9982071 and 0.9999720 respectively, resulting in an SG (20 °C/4 °C) value for water of 0.9982343.
As the principal use of specific gravity measurements in industry is determination of the concentrations of substances in aqueous solutions and as these are found in tables of SG versus concentration, it is extremely important that the analyst enter the table with the correct form of specific gravity. For example, in the brewing industry, the Plato table lists sucrose concentration by weight against true SG, and was originally (20 °C/4 °C)^{[3]} i.e. based on measurements of the density of sucrose solutions made at laboratory temperature (20 °C) but referenced to the density of water at 4 °C which is very close to the temperature at which water has its maximum density, ρ_{H2O} equal to 999.972 kg/m^{3} in SI units (0.999972 g/cm^{3} in cgs units or 62.43 lb/cu ft in United States customary units). The ASBC table^{[4]} in use today in North America, while it is derived from the original Plato table is for apparent specific gravity measurements at (20 °C/20 °C) on the IPTS68 scale where the density of water is 0.9982071 g/cm^{3}. In the sugar, soft drink, honey, fruit juice and related industries, sucrose concentration by weight is taken from a table prepared by A. Brix, which uses SG (17.5 °C/17.5 °C). As a final example, the British SG units are based on reference and sample temperatures of 60 °F and are thus (15.56 °C/15.56 °C).
Given the specific gravity of a substance, its actual density can be calculated by rearranging the above formula:
Occasionally a reference substance other than water is specified (for example, air), in which case specific gravity means density relative to that reference.
Measurement: apparent and true specific gravity [ edit ]
Pycnometer [ edit ]
Specific gravity can be measured in a number of value ways. The following illustration involving the use of the pycnometer is instructive. A pycnometer is simply a bottle which can be precisely filled to a specific, but not necessarily accurately known volume, V. Placed upon a balance of some sort it will exert a force,
where m_{b} is the mass of the bottle, g the gravitational acceleration at the location at which the measurements are being made, ρ_{a} is the density of the air at ambient pressure and ρ_{b} is the density of the material of which the bottle is made (usually glass). The second term is the mass of air displaced by the glass of the bottle whose weight, by Archimedes Principle, must be subtracted. The bottle is filled with air, but as that air displaces an equal amount of air the weight of that air is cancelled by the weight of the air displaced. Now we fill the bottle with the reference fluid, for example pure water. The force exerted on the pan of the balance becomes:
If we subtract the force measured on the empty bottle from this (or take the balance before making the water measurement) we obtain
where the subscript n indicates that this force is net of the force of the empty bottle. The bottle is now emptied, thoroughly dried and refilled with the sample. The force, net of the empty bottle, is now:
where ρ_{s} is the density of the sample. The ratio of the sample and water forces is:
This is called the Apparent Specific Gravity, denoted by subscript A, because it is what we would obtain if we took the ratio of net weighings in air from an analytical balance or used a hydrometer (the stem displaces air). Note that the result does not depend on the calibration of the balance. The only requirement on it is that it read linearly with force. Nor does SG_{A} depend on the actual volume of the pycnometer.
Further manipulation and finally substitution of SG_{V}, the true specific gravity (the subscript V is used because this is often referred to as the specific gravity in vacuo), for ρ_{s}/ρ_{w} gives the relationship between apparent and true specific gravity.
In the usual case we will have measured weights and want the true specific gravity. This is found from
Since the density of dry air at 101.325 kPa at 20 °C is^{[5]} 0.001205 g/cm^{3} and that of water is 0.998203 g/cm^{3} the difference between true and apparent specific gravities for a substance with specific gravity (20 °C/20 °C) of about 1.100 would be 0.000120. Where the specific gravity of the sample is close to that of water (for example dilute ethanol solutions) the correction is even smaller.
Digital density meters [ edit ]
 Hydrostatic pressurebased instruments
 This technology relies upon Pascal's Principle, which states that the pressure difference between two points within a vertical column of fluid is dependent upon the vertical distance between the two points, the density of the fluid and the gravitational force. This technology is often used for tank gauging applications as a convenient means of liquid level and density measure.
 Vibrating element transducers
 This type of instrument requires a vibrating element to be placed in contact with the fluid of interest. The resonant frequency of the element is measured and is related to the density of the fluid by a characterization that is dependent upon the design of the element. In modern laboratories precise measurements of specific gravity are made using oscillating Utube meters. These are capable of measurement to 5 to 6 places beyond the decimal point and are used in the brewing, distilling, pharmaceutical, petroleum and other industries. The instruments measure the actual mass of fluid contained in a fixed volume at temperatures between 0 and 80 °C but as they are microprocessor based can calculate apparent or true specific gravity and contain tables relating these to the strengths of common acids, sugar solutions, etc. The vibrating fork immersion probe is another good example of this technology. This technology also includes many coriolistype mass flow meters which are widely used in chemical and petroleum industry for high accuracy mass flow measurement and can be configured to also output density information based on the resonant frequency of the vibrating flow tubes.
 Ultrasonic transducer
 Ultrasonic waves are passed from a source, through the fluid of interest, and into a detector which measures the acoustic spectroscopy of the waves. Fluid properties such as density and viscosity can be inferred from the spectrum.
 Radiationbased gauge
 Radiation is passed from a source, through the fluid of interest, and into a scintillation detector, or counter. As the fluid density increases, the detected radiation "counts" will decrease. The source is typically the radioactive isotope cesium137, with a halflife of about 30 years. A key advantage for this technology is that the instrument is not required to be in contact with the fluid—typically the source and detector are mounted on the outside of tanks or piping.^{[6]}
 Buoyant force transducer
 The buoyancy force produced by a float in a homogeneous liquid is equal to the weight of the liquid that is displaced by the float. Since buoyancy force is linear with respect to the density of the liquid within which the float is submerged, the measure of the buoyancy force yields a measure of the density of the liquid. One commercially available unit claims the instrument is capable of measuring specific gravity with an accuracy of ±0.005 SG units. The submersible probe head contains a mathematically characterized springfloat system. When the head is immersed vertically in the liquid, the float moves vertically and the position of the float controls the position of a permanent magnet whose displacement is sensed by a concentric array of Halleffect linear displacement sensors. The output signals of the sensors are mixed in a dedicated electronics module that provides an output voltage whose magnitude is a direct linear measure of the quantity to be measured.^{[7]}
 Inline continuous measurement
 Slurry is weighed as it travels through the metered section of pipe using a patented, high resolution load cell. This section of pipe is of optimal length such that a truly representative mass of the slurry may be determined. This representative mass is then interrogated by the load cell 110 times per second to ensure accurate and repeatable measurement of the slurry.^{[citation needed]}
Examples [ edit ]
 Helium gas has a density of 0.164 g/L;^{[8]} it is 0.139 times as dense as air.
 Air has a density of 1.18 g/L.^{[8]}
Material  Specific gravity 

Balsa wood  0.2 
Oak wood  0.75 
Ethanol  0.78 
Olive oil  0.91 
Water  1 
Ironwood  1.5 
Graphite  1.9–2.3 
Table salt  2.17 
Aluminium  2.7 
Cement  3.15 
Iron  7.87 
Copper  8.96 
Lead  11.35 
Mercury  13.56 
Depleted uranium  19.1 
Gold  19.3 
Osmium  22.59 
(Samples may vary, and these figures are approximate.)
 Urine normally has a specific gravity between 1.003 and 1.030. The Urine Specific Gravity diagnostic test is used to evaluate renal concentration ability for assessment of the urinary system.^{[9]} Low concentration may indicate diabetes insipidus, while high concentration may indicate albuminuria or glycosuria.^{[9]}
 Blood normally has a specific gravity of approximately 1.060.
 Vodka 80° proof (40% v/v) has a specific gravity of 0.9498.^{[10]}
See also [ edit ]
References [ edit ]
 ^ Hough, J.S.; Briggs, D.E.; Stevens, R.; Young, T.W. (1991). Malting and Brewing Science, Vol. II Hopped Wort and Beer. London: Chapman and Hall. p. 881.
 ^ Bettin, H.; Spieweck, F. (1990). "Die Dichte des Wassers als Funktion der Temperatur nach Einführung des Internationalen Temperaturskala von 1990". PTBMitteilungen 100. pp. 195–196.
 ^ ASBC Methods of Analysis Preface to Table 1: Extract in Wort and Beer, American Society of Brewing Chemists, St Paul, 2009
 ^ ASBC Methods of Analysis op. cit. Table 1: Extract in Wort and Beer
 ^ DIN51 757 (04.1994): Testing of mineral oils and related materials; determination of density
 ^ "DSG". OHMART VEGA. VEGA Americas, Inc. Archived from the original on 4 July 2011. Retrieved 18 November 2011.
 ^ "Process Control Digital Electronic Hydrometer". Gardco. Paul N. Gardner. Retrieved 18 November 2011.
 ^ ^{a} ^{b} "Lecture Demonstrations". physics.ucsb.edu.
 ^ ^{a} ^{b} Lewis, Sharon Mantik; Dirksen, Shannon Ruff; Heitkemper, Margaret M.; Bucher, Linda; Harding, Mariann. Medicalsurgical nursing : assessment and management of clinical problems (9th ed.). St. Louis, Missouri. ISBN 9780323100892. OCLC 228373703.
 ^ "Specific Gravity of Liqueurs". Good Cocktails.com.